South East Landbased
Training Courses LLP

Chainsaw Maintenance and Crosscutting & Felling and Processing Trees up to 380mm Refresher

Duration:
1 day
Dates:

available on demand, enquire for further details

Chainsaw Maintenance and Crosscutting & Felling and Processing Trees up to 380mm Refresher Training Course

FORESTRY & ARBORICULTURE | Chainsaw Maintenance and Crosscutting & Felling and Processing Trees up to 380mm Refresher

A Refresher training course for chainsaw operatives in need of the recommended certification update required by Health & Safety Executive (HSE) guidelines - recommended every 3-5 years. Our Refresher courses are predominantly awarded by City & Guilds as CPD digital badge units.

CHAINSAW TRAINING REFRESHER COURSES AVAILABLE ARE:

Chainsaw Maintenance and Crosscutting & Felling and Processing Trees up to 380mm Refresher Course Content:

  • Understand operator safety during chainsaw maintenance
  • Be able to carry out routine and periodic maintenance to a chainsaw
  • Be able to start and check a chainsaw
  • Understand operator safety during chainsaw use
  • Be able to safely crosscut timber that is less than guide bar length in diameter
  • Identify the risk assessment and Emergency procedures on a work site
  • Select and prepare equipment required for safe and effective felling
  • Fell small trees safely and accurately using an appropriate method
  • Fell leaning trees using a safe technique
  • Remove branches safely in a manner appropriate to the branching habit
  • Crosscut stems accurately and safely to a given length and diameter
  • Stack timber using appropriate manual handling techniques

Upon Completion of the Chainsaw Maintenance and Crosscutting & Felling and Processing Trees up to 380mm Refresher, YOU’LL BE ABLE TO

  • Identify the necessary personal protective equipment required, report on its condition and locate the various standard marks
  • Identify required safety and health features on a chainsaw
  • Prepare the chainsaw for use with the correct fuel/oil mix and chain lubrication
  • Start the chainsaw from both cold and hot in a safe manner
  • Carry out pre-cutting safety tests and state the procedures if the chainsaw fails these tests
  • State the possible hazards/risks when carrying out maintenance or operational tasks
  • Organise site safety and state the procedures required
  • Select and identify correct tools to enable maintenance to be carried out and report on their serviceability
  • Carry out all routine maintenance in accordance with the awarding body guidelines
  • Cross-cut timber accurately to required lengths
  • Assess and explain the terms ‘tension’ and ‘compression’ in timber
  • Adopt safe procedures to remove a trapped guide bar
  • Identify faults and defects on a chainsaw and cutting equipment and decide which the operator can remedy and which require a service engineer’s attention
  • Handle and stack timber in a safe manner
  • Understand Biosecurity

Equipment Required for the Chainsaw Maintenance and Crosscutting & Felling and Processing Trees up to 380mm Refresher

Protective Equipment:

  • Chainsaw boots (EN 17249), Chainsaw gloves (EN 381-7), Chainsaw helmet with visor and ear muffs (EN 397/14052/12492)
  • Chainsaw trousers (all round protection is preferred – Type C (EN 381-5)
  • Personal First Aid Kit
  • A waterproof coat and over-trousers (course will continue even in rain)

Chainsaw Equipment: 

  • Serviceable chainsaw, chain with cutters of sufficient length to allow for sharpening (recommended 15 inch guide bar)
  • Combination spanner, Guide bar scraper, Round file of appropriate size with handle for sharpening chain
  • File guide (roller or other), Flat file with handle for depth gauges, Depth gauge setting tool, Clean brush for air filter cleaning
  • Chain oil and Fuel
  • Felling bar, Wedge, Lifting tongs / hooks, tape measure for measuring timber

Pre-Requisite for the Chainsaw Maintenance and Crosscutting & Felling and Processing Trees up to 380mm Refresher

Candidates must be over 16 years & hold Chainsaw Maintenance and Crosscutting 201 & 202 (CS30) and Felling trees up to 380mm 203 (CS31)

Further Information Regarding the Chainsaw Maintenance and Crosscutting & Felling and Processing Trees up to 380mm Refresher

www.nptc.org.uk

OTHER TRAINING COURSE YOU MAY BE INTERESTED IN:

You may also be interested in...

Felling & Processing Trees from 380mm-760mm

hung-up-tree-oct23-2
3 Day City & Guilds NPTC Independent Training and Assessment for experienced operators to promote and understand relevant health and safety and industry good practice....

Tree Fungi Identification

tree-fungi
One Day Certificate of Attendance to include topics: Morphological features of Fungi Groups   Fungi Habitats and Colonisation Strategies Types of Decay Diversity of Fruiting...

Utility Arboriculture

UA
Individuals who operate around utility services as part of their work in arboriculture, forestry, or other industries. It will provide the individual with the basic...

Off Road Vehicle Operating (4 x 4)

4-x-4-for-website
Boost your confidence and know-how to tackle the toughest challenges that the land – and the unpredictable British weather – can throw at you.

Mobile Elevated Work Platform

MEWP-web1
1 Day Integrated City & Guilds NPTC Training and Assessment for anyone who operates a Mobile Elevated Work Platform (MEWP) for gaining access to a work position...

Tractor Driving and Related Operations

Seltc Tractor Driving Training Course Sussex and Kent
Brush up your skills, or learn them from scratch, with our comprehensive tractor driving course. The tractor is an essential piece of machinery for so...
Course Enquiry
Full Name(Required)